Sunday, April 27, 2008

Preparing the drawer cases (5)...

I left off with the individual boards which comprise the two drawer cases. I moved on, trimmed the boards and created the joinery for the sides and top and bottom. The joinery will consist of a rabbet with some small reinforcement. I need to accurately trim the sides of the dual drawer case since there is an allowance for the middle drawer divider which needs to be taken into consideration. The accuracy revolves around the fact that I want each of the three drawers to be of the same general height.The dado for this particular divider will also be stopped, end just short of the front of the drawer case. This allows me to have the upper drawer have a lower lip to meet with the bottom drawer, hiding the center divider in the process.

In the photo, the drawer cases, not yet complete are placed sided by side and amazingly enough, there is hardly a gap between them. This allows me some flexibility in placement of the drawer cases, which has not quite been finalized yet.

Tuesday, April 22, 2008

Preparing the drawer cases (4)...

I have completed dimensioning, handplaning and scraping the surfaces of the panels for the drawer cases. The panels were longer in length than necessary, an extra length allowance of each of the panels comprises one side of each drawer case. These drawer case sides will be rabbeted into the top and bottom panels. The grain orientation of the drawer cases is similar to the cabinet top and bottom, this is purposely designed in to accommodate any expansion and contraction due to humidity changes in the ambient air. In the lower drawer case, the sides are somewhat longer to accommodate two drawers and a drawer divider. The hardwood drawer divider will be fitted into dadoed slots in the center of either side of the drawer case. Dadoes run perpendicular to grain orientation as opposed to grooves which run parallel to the grain orientation.

The drawer case sides, and top and bottom panels are oriented in the same direction to have the complete drawer case movement occur front to back similar to the cabinet itself. The drawer case sides need to be trimmed to size next and then a dado created in the dual drawer case. The drawer cases are assembled afterwards with careful attention to maintaining the drawer cases perfectly square. Once the assembly is complete, I will fit the drawer divider into its dado.

I'm anxious to begin work on the drawers and have yet to decide whether the drawer faces will be a contrasting color, most likely so. In this case, I need to find a wood which complements European Beech.

Wednesday, April 16, 2008

Preparing the drawer cases (3)...

The measurements of the boards which comprise the four drawer case panels are a tad smaller than originally planned, so I have had to forgo squaring the ends of the boards of each of eight boards. Instead I have assembled the eight boards into four panels and will instead square then ends of these panels off. It is just an arbitrary decision at this point and doesn't affect the assembly of the panels, although nicer panels would have resulted had I squared the ends of the boards first. This also allows me to dial in as much length as absolutely possible in each of the panels.

I had also jointed the mating edges of each of the boards, the edge which mates with the other, matching board of the panel. This went well and I let the boards sit for a day or so afterwards to determine if any further cupping would result. A very small bit of cupping did result, and of course it becomes more pronounced due to the width of the panels. The next step involved scribbling witness lines across each of the cupped faces of the boards and handplaning the outside edge area working towards the middle. I regularly go back and forth with a flat, steel rule to determine how much progress is being made. I also try not to overshoot... which essentially decreases the overall thickness of each of the boards.

At this point, I have four panels ready to be squared to finish dimensions, both in width and length. A small part of each of the panels form the sides of the drawer case. I will also need to cross cut these sections off, which leaves me with four shorter panels which form the tops and bottoms of the drawer case.

I'm going to take some time and spend it outdoors today. We had wintry weather until late last week, but this week has been getting wamer and sunnier with temps in the low 70's today. We've had such a long winter up here, and this weather couldn't arrive soon enough.

Sunday, April 13, 2008

Preparing the drawer cases (2)...

I left off in the previous post with a few boards to flatten and smooth with handplanes. I typically use a planing board with a plane stop at the end to perform this type of work. The boards are relatively small and are easily held against the plane stop. This allows me to quickly flip the board around to plane either side without needing to clamp the board again. If I were planing a larger panel I would most likely fasten it between bench dogs.

The handplaning of these particular boards is straightforward along their length with little diagonal planing... so it works out well. Handplaning these boards which will comprise the panels for the drawer cases begins with a long fore or jointer plane to flatten the faces of the boards and ensure they are flat and parallel to each other. I also have the final thickness of each board in mind and work towards this. After the individual boards were resawn a little cupping was introduced , inherent to resawing, and although acclimatization to the studio environment helps to relieve this cup and any other tension in the boards, some minimal cupping remains in each of these boards.

I use a jointer plane in this case, I have it tuned and ready most of the time for work like this. A shorter fore plane would also be ideal since the boards are relatively short in length. Once the boards faces are flat with parallel faces I then move on to a finely tuned smoother plane to ensure the faces of the boards are flat as can be. The term which is used for this type of board preparation is four-squaring the board which ensures that both faces and the two long edges are parallel to each other, and the ends and edges are perpendicular. After completing this process on each of the other boards which will comprise the drawer case panels, I will be squaring the ends to achieve both the correct length of each board and to ensure the boards are perfectly square.

Saturday, April 12, 2008

Preparing the drawer cases (1)...

After slicing (resawing) and dicing (ripping, cross-cutting) the rough blanks for the interior parts, I am now left with a few fairly identically sized boards. The individual boards are thicker than the final dimension to allow for any cupping ,bowing, or twist that may result from the resawing operation and acclimatization of the boards. I have also resawn a few extra boards to allow for any problems or mismatched grain when creating the wider panels for the drawer cases. The boards are fairly similar in width but differ in length. Half are destined for the single drawer case, the other half to the stacked drawer case. Some wane or bark can be seen on a few of the boards and this will be trimmed off to create square edges with minimal removal.

I will let these boards sit on edge for a day or so and then proceed with hand planing them closer to the final thickness. Once the "approximate" final thickness is achieved, the next step in the sequence is to square the mating edges and join these boards to create the panels for the drawer cases. There are two approaches to creating the panels, either glue the boards up initially and hand plane or surface the panel to final thickness or ..... hand plane the individual boards close to final thickness and then join to make a panel. I prefer the latter as any strange characteristics of each board will be manifested before joining. This allows me to substitute one board for another, more stable board. Of course, there is a little final hand plane surfacing to complete the thicknessing to size step, but very minimal.

Friday, April 11, 2008

Selecting wood for the interior...

After having decided on a layout for the interior, I proceeded to take measurements of the
drawer case mockups. With these measurements in hand, I then create a cut list. The cut list provides me a clear idea of the amount of wood necessary to make both the drawer cases. The cut list also allows me to optimize the individual components for the drawer cases in order to minimize the wood necessary. This is only valid to a point however, as the wood components need to be selected with careful consideration to grain orientation and to maintain the harmony of the individual drawer cases.

With this information in hand, I selected an area of a large beech plank to cut my blanks from. Fortunately, I have some very nice European Beech planks in my studio I had acquired a while ago. The planks are rift to quarter-sawn in grain orientation and fairly thick at approximately 2.5 inches. The blanks are slightly different in size and are rift-sawn. The difference in blank size is attributed to the different size of either of the drawer cases. In the photo above, the two blanks can be seen along with my measurements and cut list. I also drew the components of the drawer cases out on another sheet of cardboard as a visual aid in laying out the components. Since the depth of the drawer cases is fairly large, I will be gluing two pieces of beech for each of the tops, bottoms and sides of the drawer cases. In doing this, I will try to maintain grain orientation and harmony to create fairly seamless components for the drawer cases.

Next I will layout and mark the boards to be cut from both of these beech blanks. After cutting the blanks in half and squaring one face and one edge of the individual halves , I will slice the boards off using a bandsaw similar to resawing.

Monday, April 7, 2008

Cabinet interior mock up...

I have been mocking up a few different layouts for the interior of the cabinet in the past few days. There are certain criteria which need to be considered in this process. The original design calls for three drawers with maximized interior space for art objects. One of the factors used in the design of the layout is the height and width of the cabinet itself and allowing as much room for taller art objects. This space will co-exist with the three drawers. Initially, I designed the drawers on the right hand side of the cabinet interior with two lower drawers, a space for art object(s), and a drawer above. I had also considered shelving in the design but decided against this as the height of the cabinet would further limit any taller art objects from being displayed.

In the photo, is my latest design of the interior. This layout is a good example of the design adage, "less is sometimes more". There is a fair amount of room on both the left and right side of the cabinet interior. The drawers have been divided into two assemblies with one drawer at the top left and two drawers at the bottom right of the cabinet interior. The design is also somewhat interesting and does not conform to the typical, established layout of drawers within a cabinet. This feature enhances the uniqueness of the cabinet interior in my opinion.

This design is not quite cast in stone as yet. I intend to further refine the layout with both interesting, unique design and optimized space as criteria. Mocking up is a great exercise in the design process, both initially and in finalizing the design. Having the components of a furniture piece mocked up to scale proportions reveals any design considerations which might have been overlooked in the initial design.

Sunday, March 23, 2008

Cabinet taking shape...

I now have the cabinet case, back panel , and front doors installed and adjusted. Everything looks fine at this point, with my next emphasis on the interior of the cabinet. Afterwards, I will finalize the design of the cabinet stand. With respect to the interior, I have a design idea in mind and have begun to make a few sketches. I will most likely leave the left hand side of the interior free and clear and build up the right with two stacked drawers and perhaps a third drawer further up. This design allows the right hand door to be opened independently in the sense that drawers can be accessed without the need to open both doors. This part of the design is interesting and helps me to resolve the division of the interior compartments.The client has indicated I have carte blanche to design the interior as I wish with the only requirement to have one large and one smaller space for art objects, along with two drawers. Sometimes less is more and in this case ( no pun intended) the larger the non-drawer compartments, the larger the objects which can be showcased.

In the photo, I use tape as temporary door pulls while I decide on the door pull design. I'm debating whether to simply have one pull located on the right hand door. If I decide on one door pull, I will elaborate on the thought process leading to this decision.

After my return from a ski trip this week I will be dedicating the next few days to finalizing the design of the interior and beginning to create it. On this ski trip, my wife and I are staying in a small resort town with surrounding towns that have plenty of small shops and boutiques. We both plan to glean some fresh design ideas from other visual objects, not necessarily wood objects... and inspiration for this piece of furniture and other, future designs along with inspiration for her wood inlay jewelry designs.

Friday, March 21, 2008

Contrasting stiles...

A cherry cabinet on stand I built three years ago had developed a small bow in the inside vertical stile of the right hand door. This happened a few weeks after I completed it. I kept telling myself I would one day either make some new doors or replace the bowed stile in the right hand door. Well, I finally decided to do this. I hunkered down , disassembled the right hand door and replaced both the inside lipped stile and the top rail. The cherry cabinet was originally finished with multiple thinned coats of super blonde shellac. Cherry develops a wonderful color and patina as it ages. There is no sense in staining this particular wood as the natural aging process and exposure to light and air provide the most beautiful color. We had this cabinet around for the past three years as it slowly developed the cherry patina. It is sometimes difficult to appreciate how much of a color change has actually occurred since the cabinet ages uniformly.

Well, I found out how much it aged and developed a dark color when I began to replace parts of the right hand cabinet door. The photo has the inner lipped stile and the top rail as fresh, new wood. I made sure to have these two pieces acclimate in my studio for a couple of weeks. The contrast is incredible... with nothing originally applied to the cherry cabinet but super blonde shellac and wax, no stain of any type applied. I took this photo to be able to show any prospective clients just how much cherry changes over time.

I notice the issue of either staining or leaving cherry to develop it's own aged color comes up occasionally in forums and the overwhelming advice given is to let it develop its own color over time. When you see the difference, it is easier to accept this advice.

I thought I would share this..

Wednesday, March 19, 2008

Door lip and rabbet...

Rather than leave an open gap between the doors, even a small one, it is much preferred to create a mating set of lip and rabbet along the inner edges of the front door panels. This serves to provide a positive closure of the doors and masks the very small reveal between the doors. In this particular case , I create an outside lip or rabbet on the right hand door as this is the first door opened. The method I utilize is to mark the outline of the rabbet, in my case 1/4 in. X 1/4 in. and begin to remove material at the edge of the right hand door. The wood removed is part of the hardwood edging I installed within the door panel edges prior to veneering. The tool I use is a skew rabbet block plane with adjustable fence. This particular plane is based on the Stanley No. 140 plane. I added a wood auxiliary fence to the plane to extend the bearing surface of the plane against the edge of the door panel.


This process went along fairly well without any surprises and afterwards I re-installed the door and began to fit the mating edge to it. This rabbet will mate perfectly with the right hand door edge. Rather than concern myself with a slightly wider left hand door I add a lip of the same wood and grain orientation to the inner edge of the left door instead. This allows me to create two identically sized door panels and since veneer is involved, the complexity of the process is simpler if the door panels are of equal dimensions.


I currently have the left hand door rabbeted edge in the process of glue-up and afterwards I will perform any small trimming to ensure the fit is perfect between the doors. There is a small, slightly greater than 1/32 in. gap between the doors at the moment which will have less of a reveal apparent once the lipped edges are created and installed.


Tuesday, March 18, 2008

Door panels (4)...

Once the mortises for the knife hinges are successfully created and care is taken to make certain the offsets are uniform and the depth of each knife leaf is consistent, the next step is to temporarily install the doors while fitting each door to the cabinet. The reveal around each door is important as well as any small differences in how the doors hang within the cabinet frame. In this photo the cabinet is reversed in orientation top to bottom for me to work on the fitting. The left door is in the photo. The knife hinges have a very small amount of leeway for me to adjust the doors so the reveal at both the top and bottom and the center part between doors is uniform.

I also need to be conscious of how the outside edges fit the cabinet , they need to be parallel and in the same plane as the cabinet sides. The fitting of the doors can be somewhat time consuming but in my opinion this needs to be done correctly at this stage or the visual impact of a non-uniform reveal will be very apparent later.

After completing this fitting and knife hinge adjustment I will be creating the lip at the juncture of the doors in the middle of the cabinet. The lip serves to hide any open space between the doors and also to create an interlocking, positive closure for the doors. The right hand door will have a rabbeted lip whereas the left hand door will have a additional piece of beech added to the rear of the center edge of the door to form a mating lip. To maintain grain matching I have pieces of beech left over from the same plank I used to resaw the veneers earlier.

We have plenty of snow up here at this time , more than the average winter, and my wife and I will be leaving for a skiing trip at a resort next week. We're both crazy about spring skiing and there is plenty of nice weather coming up.